== Keysight B150xA Series Easy Test Navigator Software 1.2.3.0 Release Notes ==

== CORRESPONDING FIRMWARE REVISION ==
This revision of software works with the following firmware.

  - B150xA Series: A.06.00 or later

== IMPROVEMENTS ==

  - [9533] [Datasheet] Setup parameter adjusment is to be fed back into test condition input field.

  - [9547] [Gate Charge] IGBT Qg curve fitting is to be refined for case of negative Vge(off).

  - [9551] [Power Loss] Should read measurement data according to the name instead of the order.

  - [9553] [IV] Catch and report an unhandled exception in the thread of UI.

  - [9597] [Power Loss] Relaxation of extraction constraints for Rg

== FIXED DEFECTS ==

  - [9542] [Graph] Trace edge point in graph is to be rounded.

  - [9549] [Datasheet] The label of trace may be placed outside the frame of graph.
  
  - [9552] [IV] When the oscilloscope view has no data, mouse dragging with CTRL key pressing causes crash.

  - [9555] [Device Capacitance] Drain bias input may be disabled even in case of drain bias connection.

  - [9573] [Datasheet] In case of B1506AH21, IGES(-) for IGBT is not prepared.

  - [9575] [Datasheet] File filter for importing device symbol image is to be added.

  - [9581] [IV] Compensation of voltage drop for gate/drain resistance is not applied.

  - [9587] [Gate Charge] Modal calibraiton dialog can go behind of main window and lose operability.

  - [9589] [Datasheet] In case of component test, same connection instruction is always shown for thermo-trigger.

  - [9598] [Common] The first measurement after fixture resetting may be aborted unexpectedly.

  - [9599] [Gate Charge] SMU over-range isn't considered in parasitic capacitance correction.

  - [9606] [Gate Charge] Current load adjustment for Id(on) of 20A may fail in case of B1506AH21 (HCSMU).

  - [9612] [IV] Nomenclature for MOSFET is used for IGBT for step parameter name.

  - [9613] [Gate Charge] Extraction of Qg(on), Qg(th) and Qgs are to be updated for derived Qg.

  - [9616] [Datasheet] Graph of the positive log scale with the minus value can't be printed in XPS.

  - [9620] [Datasheet] Memory usage may increase for successive opening of ETN DS file.

  - [9630] [B1506AH71/H51] UHCU failure is indicated as MCSMU failure until performing Self Test.

  - [9632] [Power Loss] Null Reference Exception may occur after editing NaN Value.

== REVISION HISTORY ==
<Software 1.1.16.0>

 New Features:

  - Oscilloscope View in I/V Measurement

  - Component Test in Datasheet Characterization

  - IGBT support in Power Loss Calculation

  - Output Capacitance Loss in Power Loss Calculation

  - [9512] [Datasheet] Saving in text format is to be supported.

 Improvements:

  - [9456] [Device Capacitance] Immittance data component displayed on graph is to be saved in data file.
  - [9457] [IV] RGS for graph data is to be supported.
  - [9469] [Graph] Data and scale setting are to be saved in setup file.
  - [9482] [Graph] Polarity of end points are to be kept for changing with mouse wheel operation.
  - [9483] [Graph] Support of simple operation for changing graph scale using mouse.
  - [9497] [Datasheet] Alias for data name in graph trace label is to be supported for appropriate expression.
  - [9503] [Gate Charge] S2 of derived JESD24-2 is to be identical to S2 of High Current JESD24-2.
  - [9505] [Gate Charge] S1 of derived JESD24-2 is to be identical to S1 of High Voltage JESD24-2.
  - [9507] [IV] Default aperture and step time for staircase sweep is to be extended.
  - [9514] [Datasheet] Limitation to min./max. range for parameters by related maximum rating is to be supported.
  - [9522] [Power Loss] Default sweep settings are to be updated to practical settings.
  - [9530] [Datasheet] Power compliance is to be applied in MOSFET > VDS-VGS for B1506AH21.
  - [9531] [Datasheet] Improvement in scrolling by scroll button.
  - [9536] [Common] Default input value options for numeric input field.
  - [9541] [Datasheet] Each measurement data is not to be saved in corresponding measurement DataStore in case of Datasheet execution.

 Fixed Defects:

  - [9454] [Datasheet] Maximum ratings are not applied to duplicated measurement items.
  - [9459] [Graph] Domain marker shift amount by rotary knob is not propotional to domain scale.
  - [9463] [Common] Path for save setup operation is to be nullified by opening data file.
  - [9484] [PowerLoss] Calculation of Irms is not the root mean square of drain current.
  - [9486] [PowerLoss] Inconsistent combination of Id/Ic, Irms and D can be set.
  - [9495] [Common] Input parameter values will be rounded inconsistently.
  - [9515] [PowerLoss] Calculation result of Conduction Loss is incorrect if Id/Ic or D is specified as a sweep parameter.

<Software 1.0.7.0>
 New Features:

  - Initial release for B1506A and B1507A